Research Status of Friction Interface Evolution Mechanism of Non-magnetic Steel
DOI:
https://doi.org/10.62051/ijmee.v2n3.01Keywords:
Non-magnetic Steel, Rotary Friction Welding, Corona-bondAbstract
The non-magnetic drill pipe (composed of male and female thread joints and rod bodies) is the key component of the directional drilling technology equipment for gas extraction in coal mine tunnels. The thread joint and the drill pipe body are connected by continuous drive friction welding. In the study, it was found that the banded structure appeared in the joint of continuous drive friction welding of non-magnetic steel, which reduced the strength of drill pipe. At the same time, it is found that the heat flow mode is one of the key factors affecting the banded structure, and the heat flow mode is based on the evolution of the interface plastic ring. In this paper, through the review of the research status of the interface evolution law of non-magnetic steel continuous drive friction welding, the experimental method for the study of the interface evolution law of non-magnetic steel continuous drive friction welding is found.
References
Spindler D E What industry needs to know about fi ction welding[J]. Welding Joumal, 1994, 5:37~42.
Jin F, Li J L, Du Y J, et al. Numerical simulation based upon friction coefficient model on thermos-mechanical couping in rotary friction welding corresponding with corona bond evolution[J]. Journal of Manufacturing Process, 2019, 45: 595~602.
Crossland B. Friction welding[J]. Contemporary Physics, 1971, 12(6): 559~574.
Satyanarayana V G, Madhusudhan R, Mohandas T. Continuous drive friction welding studies on AISI 304 austenitic stainless steel welds[J]. Materials and Manufacturing Processes, 2004, 19(3): 487~505.
Udayakumar T, Raja K, Abhijit A T, et al. Experimental investigation on mechanical and metallurgical properties of super duplex stainless steel joints using friction welding process[J]. Journal of Manufacturing Processes, 2013, 15(4): 558~571.
Ajith P, Sathiya P, Aravindan S. Experimental Investigation on Friction Welding of UNS S32205 Duplex Stainless Steel[J]. Acta Metallurgica Sinica, 2014, 27(6): 995~1007.
Vill V I. Friction welding of metals[M]. American Welding Society; trade distributor: Reinhold Pub. Co, 1962: 27~33.
Crossland B. Friction welding[J]. Contemporary Physics, 1971, 12(6): 559~574.
Duffin F, Bahrani A. Frictional behaviour of mild steel in friction welding[J]. Wear, 1973, 26(1): 53~74.
Hasui A, Fukushima S. On the torque in friction welding[J]. Transactions of the Japan Welding Society, 1977, 8(1): 26~32.
Francis A, Craine R. On a model for frictioning stage in friction welding of thin tubes[J]. International Journal of Heat and Mass Transfer, 1985, 28(9): 1747~1755.
Hasegawa M, Ieda T. Effects of friction welding conditions on initial joining phenomena[J]. Welding international, 1999, 13(9): 701~711.
Kimura M, Seo K, Kusaka M, et al.. Observation of joining phenomena in friction stage and improving friction welding method[J]. International Journal Series A: Solid Mechanics and Material Engineering, 2003, 46(3): 384~390.
Kimura M, Kusaka M, Seo K, et al. Effect of friction speed on initial seizure portion on welded interface–study of joining mechanism of friction welding (Report 4)[J]. Quarterly Journal of the Japan Welding Society, 2003, 21: 615~622.
Kimura M, Inoue H, Kusaka M, et al. Analysis method of friction torque and weld interface temperature during friction process of steel friction welding[J]. Journal of Solid Mechanics and Materials Engineering, 2010, 4: 401~413.
Kimura M, Choji M, Kusaka M, et al. Effect of friction welding conditions and aging treatment on mechanical properties of A7075-T6 aluminum alloy friction joints[J]. Science and Technology of Welding and Joining, 2013, 10(4): 406~412.
Li P, Li J L, Li X, et al. A study of the mechanisms involved in initial friction process of continuous drive friction welding[J]. Journal of Adhesion Science and Technology, 2015, 29(12): 1246~1257.
Xiong J T, Li J L, Wei Y N, et al. An analytical model of steady–state continuous drive friction welding[J]. Acta Materialia, 2013, 61(5): 1662~1675.
Li W Y, Wang F F. Modeling of continuous drive friction welding of mild steel[J]. Materials Science and Engineering: A, 2011, 528(18): 5921~5926.
Wang D, Ni D R, Xiao B L, et al. Microstructural evolution and mechanical properties of friction stir welded joint of Fe-Cr-Mn-Mo-N austenite stainless steel[J]. Materials and Design, 2014, 64: 355~359.
Zhang H, Wang D, Xue P, et al. Microstructural evolution and pitting corrosion behavior of friction stir welded joint of high nitrogen stainless steel[J]. Materials and Design, 2016, 110: 802~810.
Du D X, Fu R D, Li Y J, et al. Gradient characteristics and strength matching in friction stir welded joints of Fe-18Cr-16Mn-2Mo-0.85N austenitic stainless steel[J]. Materials Science and Engineering A, 2014, 616: 246~251.
Li H B, Jiang Z H, Feng H, et al. Microstructure, mechanical and corrosion properties of friction stir welded high nitrogen nickel-free austenitic stainless steel[J]. Materials and Design, 2015, 84: 291~299.
Ma H, Qin G L, Geng P H, et al. Microstructure characterization and properties of carbon steel to stainless steel dissimilar metal joint made by friction welding[J]. Materials and Design 2015, 86: 587~597.
Hazra M, Rao K S, Reddy G M. Friction welding of a nickel free high nitrogen steel: influence of forge force on microstructure, mechanical properties and pitting corrosion resistance[J]. Journal of materials research and technology, 2014, 3(1):90~100.
ASM International. ASM handbook welding, brazing and soldering[M]. Materials Park, OH, 1993, 504~506.
Jin F, Li J L, Liu P, et al. Friction coefficient model and joint formation in rotary friction welding[J]. Journal of Manufacturing Process, 2019, 46: 286~297.
Jin F, Li J L, Du Y J, et al. Numerical simulation based upon friction coefficient model on thermos-mechanical couping in rotary friction welding corresponding with corona bond evolution[J]. Journal of Manufacturing Process, 2019, 45: 595~602.
Crossland B. Friction welding[J]. Contemporary Physics, 1971, 12(6): 559~574.
Satyanarayana V G, Madhusudhan R, Mohandas T. Continuous drive friction welding studies on AISI 304 austenitic stainless steel welds[J]. Materials and Manufacturing Processes, 2004, 19(3): 487~505.
Udayakumar T, Raja K, Abhijit A T, et al. Experimental investigation on mechanical and metallurgical properties of super duplex stainless steel joints using friction welding process[J]. Journal of Manufacturing Processes, 2013, 15(4): 558~571.
Ajith P, Sathiya P, Aravindan S. Experimental Investigation on Friction Welding of UNS S32205 Duplex Stainless Steel[J]. Acta Metallurgica Sinica, 2014, 27(6): 995~1007.
Li X, Li J L, Liao Z X, et al. Effect of rotation speed on friction behavior and radially non-uniform local mechanical properties of AA6061-T6 rotary friction welded joint[J]. Journal of Adhesion Science and Technology, 2018, 32(18): 1987~2006.
Li X, Li J L, Liao Z X, et al. Effect of rotation speed on friction behavior of rotary friction welding of AA6061-T6 aluminum alloy[J]. Welding in the World, 2018, 62(5): 923~930.
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
